soundcore Motion X600 Review

We may earn a commission from some links on this page.

The soundcore Motion X600 is a portable wireless speaker built around spatial audio. An upward-firing full-range driver sits on top of the cabinet, two woofers and two tweeters handle the rest, and the amplifier is rated at 50W. Bluetooth 5.3 handles the connection, LDAC is available through the soundcore app on Android, and the battery is rated for 12 hours at a quarter of the volume. It is IPX7 waterproof and light enough to carry between rooms. Here is what the maker lists and where that design helps or limits you.

Key Takeaways

  • An upward-firing driver plus two woofers and two tweeters aim to spread sound around the room rather than from one point.
  • 50W of output and a frequency range that extends to 40 kHz, with Hi-Res and LDAC support.
  • Playtime is rated at 12 hours at a quarter volume with Bass Mode off, and a charge takes about six hours.
  • IPX7 waterproofing and a portable build suit moving it between rooms or taking it outside.
  • The soundcore app adds a custom EQ, an LDAC switch and firmware updates.

Spatial Audio Design

The Motion X600's party piece is the driver layout. Soundcore puts a full-range driver on top of the cabinet, firing upward, and adds two woofers and two tweeters around the sides. The idea is to use the ceiling and the walls to spread sound, so a listener hears a wider stage than a conventional forward-facing speaker gives.

Soundcore describes the result as multidimensional, with detail that stays separate across the range. The upward driver is the part that separates the X600 from a standard portable speaker; the woofers and tweeters handle the low end and the sides of the stage.

At 50W, the speaker is aimed at a room rather than a desk. Soundcore recommends it for a bedroom or living room and says it is light enough to move between them, which is the practical advantage of a portable design over a fixed home speaker.

Sound Quality

Soundcore rates the X600 for Hi-Res audio and a frequency range up to 40 kHz. LDAC, the high-bitrate Bluetooth codec, is supported on Android 8.0 and above, but it has to be switched on in the app rather than enabled out of the box.

A single X600 plays stereo. Soundcore says the left side handles the left channel and the right side the right channel, so you do not need a second unit to get separation between the two.

For tuning, the app has a custom EQ with presets and a Pro EQ you can adjust and share. Bass Mode is a separate option, and Soundcore notes that the 12-hour battery rating assumes Bass Mode is off. Two X600s can also be paired in TWS mode when one speaker is not enough for the space.

Detailed Features

The X600 combines a portable cabinet with the driver count of a small room speaker. The table below collects the figures soundcore lists on the product page.

Output50W
DriversUpward-firing full-range driver, two woofers and two tweeters
Playtime12 hours at a quarter volume with Bass Mode off
Water resistanceIPX7
Bluetooth5.3
CodecsHi-Res and LDAC (LDAC on Android 8.0 and above)
InputsBluetooth, AUX in, USB-C charging
AppCustom EQ, LDAC switch, firmware updates, voice prompts
ExtrasBuilt-in microphone, stereo from one unit, TWS pairing

Setup and Controls

Setup runs through Bluetooth: pair the speaker, then install the soundcore app to reach the EQ, the LDAC switch and firmware updates. Soundcore says peak performance needs the app and the latest firmware.

Charging uses USB-C. The box includes a 60 cm USB-C to USB-C cable but no wall charger and no aux cable, so you need your own 5V/3A adapter for the stated six-hour charge time.

Controls sit on the speaker itself, including a recessed power button that is easier to find in low light. Voice prompts can be turned off in the app, and the built-in microphone means you can take calls through the speaker.

Advantages and Disadvantages

The case for the X600 rests on its driver layout and its portability, while the limits come from the same design choices.

  • Advantage: the upward-firing driver gives a wider presentation than a typical portable speaker.
  • Advantage: 50W is enough output for a bedroom or living room.
  • Advantage: IPX7 protection and a light cabinet make it easy to move outside.
  • Advantage: LDAC and the custom EQ suit higher-quality sources on Android.
  • Disadvantage: the spatial effect depends on the room and on where you place the speaker.
  • Disadvantage: LDAC needs an Android phone and a trip into the app.
  • Disadvantage: the 12-hour rating drops with bass, volume and LDAC.
  • Disadvantage: there is no wall charger in the box.

Battery and Charging

Soundcore rates playtime at 12 hours, measured at a quarter of the volume with Bass Mode off. Turning the volume up, leaving Bass Mode on or using LDAC will shorten that figure.

A full charge takes around six hours with a certified 5V/3A charger. There is no fast-charge claim, so plan it as an overnight charge rather than a quick top-up before a party.

The USB-C port sits under a waterproof cover on the back. Soundcore says the cover must be secure before the speaker goes near water, so it is worth checking every time you unplug the cable.

Frequently Asked Questions

Does the Motion X600 Need the soundcore App?

No for basic playback: you can pair it over Bluetooth and play without the app. The app is needed for the custom EQ, LDAC, voice-prompt settings and firmware updates.

Can One Speaker Play Stereo?

Yes. Soundcore says the left side plays the left channel and the right side plays the right channel from a single unit.

Is the Motion X600 Waterproof?

It is rated IPX7. Soundcore notes that the waterproof cover on the back must be fastened before the speaker is submerged.

How Long Does It Take to Charge?

About six hours with a certified 5V/3A charger. The box includes a USB-C cable but no charger.

Can You Pair Two Motion X600 Speakers?

Yes. Two Motion X600 speakers can be paired in TWS mode for wider coverage across a room.